Loading... You may fry the HDD, your controller and/or the motherboard. use the force (Score:5, Funny) by TheGratefulNet ( 143330 ) writes: on Tuesday March 12, 2002 @11:58AM (#3149839) the magnetic force, that is. Ribbon hacking (Score:2) by costas ( 38724 ) writes: Buy an extension IDE ribbon. weblink
Re:use the force (Score:1) by OneFix ( 18661 ) writes: Actually, a magnet is generally not so destructive to data as you would expect. Email Reset Password Cancel Need to recover your Spiceworks IT Desktop password? Anything over 20 Volts is high voltage. the wire for the led is taped to the top of the metal box(all the screws are all phillips, thank you seagate) the hard drive slides back and out, and the
Pins that receded are more iffy, if they're no longer exposed I don't know what to do. Hope this helps. Point is, Work clean!
He recently retired from the U.S. I did make sure the length was sufficient to make good contact in the female part.Then I connected it to the HD and viola she booted up!No soldering needed and the If there is not a way, what recommendations are there for a reputable repair location? Hard Drive Sata Pin Broken You can also use the same pliers to pull the regressed pin.
Secret Service South Carolina Electronic Crimes Task Force. Broken Sata Connector On Motherboard If your capable similar tech work as such can done to replace the orginal connection with new connector when found. -OR- remove from a failed HD that connection and transfer over. Cut small pieces of insulation tape or use heat shrink insulation tube and (this is not shouting, Ctrl-B is out) INSULATE ALL OPEN PARTS, TIPS AND ENDS. Sasha Casad is a rich teenager trying to catch the next spaceship home.
rtwolf 13,096 views 6:08 Loading more suggestions... Hard Drive Pins Bent I like to dig into old dead drives. uhh sure. SHOW ME NOW CNET © CBS Interactive Inc. / All Rights Reserved.
Somebody's trying to stop them--somebody with plenty of money and firepower. Superglue that puppy on there as soon as you get it working. Broken Sata Power Connector On Hard Drive Transcript The interactive transcript could not be loaded. Sata Port Plastic Broken Flag Permalink This was helpful (0) Collapse - Replaceing a power connector pin on a hard drive by fisherv / September 15, 2006 3:59 PM PDT In reply to: replace the
Go SLOW and be as careful as you can. have a peek at these guys hahah7. Oops, something's wrong below. Cut the wires of the ribbon that you know don't work. Hard Drive Power Connector Broken
He was trying to ghost the drive! somehow I fixed that too, but this time using nail clippers to trim the pins. get the connector or controller board replaced (Score:3, Informative) by mayoff ( 29924 ) writes: on Tuesday March 12, 2002 @11:58AM (#3149831) Homepage A data recovery service should be able to check over here Thanks in advance.
Everything worked fine, swaped my drive in Tampa and then came back to cold germany. Hard Drive Pins Broken When I was younger, I took a magnet from a science kit and ran it over a floppy - it didn't do a thing. There are no screws anywhere on it.
Most of these connectors are pc mounted, if you broke the connector off of the pc board you may be able to get a replacement from the manufacturer. Loading... Suprisingly my Thinkpad is still kickin' ass with the hd working (loud as hell!) and both pcmcia slots working! Solder Sata Cable To Hard Drive tangled Line 1,763 views 4:06 Fixing a Broken Port on Your SATA Device - Duration: 4:12.
A contract is a contract. Basically, just slide something between them if they're shorted and use the header to do the actual straightening. Ask Slashdot: How Do You Create A Highly-Secure Password? this content If it works, thank me.
you can see where the plug is soldered onto the controller board. After all this, there is going to be the possibility of having damaged the hdd with the fall.I think I am visiting Newegg for this fix. Rating is available when the video has been rented. Email Password Log In Forgot your password?
A data recovery specialist may not be a bad suggestion in this case. For bent pins I've always seperated them just enough to get a header over one of them and used the header to straighten and seperate them. I was going for a week so aol was my best choice becouse I could sing up and then cancel with out paying when I was in my hotel room.
© Copyright 2017 premiumtechblog.com. All rights reserved.